Spin halyard parker

Sails & Tuning

Moderator: forumadmin

Postby evanwellens » Wed Apr 07, 2010 4:42 pm

Anyone tried this
http://www.apsltd.com/c-3186-j80sparparts.aspx
Seems like a good idea and was curious if someone who has it installed could give some feedback
evanwellens
 
Posts: 34
Joined: Wed Dec 31, 1969 8:00 pm

Postby Guest » Thu Apr 08, 2010 8:41 pm

We've been using it for about 6 months and it works great as long as the crew remembers to un-park the cleat prior to a drop.

[Posted by: randy
]
Guest
 

Postby evanwellens » Tue Apr 27, 2010 10:54 am

Thanks Randy , any chance you could share info on how you installed it ? can't you unpark from the cockit, it looked that by pulling from there it would unpark... No ?
evanwellens
 
Posts: 34
Joined: Wed Dec 31, 1969 8:00 pm

Postby Guest » Tue Apr 27, 2010 3:30 pm

That's right, install it on the mast. It allows you to hoist from the mast and temporarily cleat halyard on mast. After the hoist you can pull the halyard through the cabin top cleat from the cockpit and it will unpark. If there is alot of pressure from strong wind you may have to put haylard on a winch to get the cleat on mast to unpark but not usually a problem.

[Posted by: randy
]
Guest
 

Postby beauly » Tue Apr 27, 2010 3:36 pm

So the concept with this "parker" is to allow you to control that halyard from the cockpit, and not always only from the mast? Particularly for take downs? - so you don't have to send someone to the mast?
beauly
 
Posts: 25
Joined: Wed Dec 31, 1969 8:00 pm

Postby danieljcpa » Sat May 01, 2010 11:22 am

When attaching the fitting to the mast, do you use sheet mettle screws or tap it for a #10 screw?
danieljcpa
 
Posts: 25
Joined: Wed Dec 31, 1969 8:00 pm

Postby evanwellens » Sun May 02, 2010 6:38 pm

Any advice on installation would be great as we're really anxious to get it going.

Thanks
evanwellens
 
Posts: 34
Joined: Wed Dec 31, 1969 8:00 pm

Postby danieljcpa » Fri Oct 01, 2010 2:17 pm

we installed the parking cleat using 10-32 machine screws. we tapped the mast and set the cleat slightly offset from the direct line between the block on the bottom of the mast and the exit hole.

We also used Locktight to lock the threads in place.

We did this for 2 reasons. First the positioning on the mast that would have been in line was on a section of the mast that was too curved for the fitting to sit right. Second the offset makes it easier to uncleat the parker from the cockpit while the sail is still under a load.



We love the new process of setting the sail but sometimes forget to uncleat the parker when we flake the halyard to prepare it for lowering...we'll just have to work on that.<img src="http://j80.org/discus/messages/6/918.jpg" alt="Wasaaabi at Huntington Lake">
danieljcpa
 
Posts: 25
Joined: Wed Dec 31, 1969 8:00 pm

Postby evanwellens » Fri Oct 01, 2010 5:21 pm

Interesting we just got it installed a few weeks ago and in our expierience it's nearly impossible to release loaded from the cockpit, How high did you install it ?
evanwellens
 
Posts: 34
Joined: Wed Dec 31, 1969 8:00 pm

Postby firebolt » Fri Oct 01, 2010 5:38 pm

We installed it using the two holes from the original cleat that was there, about six inches below the exit from the mast and slightly forward. We have not had any problem snapping it out from the cockpit. (see picture)
<img src="http://j80.org/discus/messages/6/930.png" alt="Spin Halyard Setup">
firebolt
 
Posts: 11
Joined: Wed Dec 31, 1969 8:00 pm


Return to Sails & Tuning

Who is online

Users browsing this forum: No registered users and 1 guest